DG201ABK DATASHEET PDF

DGABK datasheet, DGABK pdf, DGABK data sheet, datasheet, data sheet, pdf, Intersil, Quad SPST, CMOS Analog Switches. DGABK Datasheet, DGABK PDF, DGABK Data sheet, DGABK manual, DGABK pdf, DGABK, datenblatt, Electronics DGABK. DGABK datasheet, DGABK circuit, DGABK data sheet: MAXIM – Quad SPST CMOS Analog Switches,alldatasheet, datasheet, Datasheet search site.

Author: Sajas Kazisar
Country: Uruguay
Language: English (Spanish)
Genre: Video
Published (Last): 1 July 2018
Pages: 57
PDF File Size: 9.45 Mb
ePub File Size: 5.59 Mb
ISBN: 860-9-77000-322-5
Downloads: 84149
Price: Free* [*Free Regsitration Required]
Uploader: Feshakar

Pin Configurations continued To provide protection for overvoltages up to 20V above the supplies, a 1N or 1N type diode should be placed in series with the positive and negative supplies as shown in Figure 2. Dimension Q shall be measured from the seating plane to the base plane. For more information on TYP values see Note 3. VO is the steady state output with switch on.

E and eA are measured with the leads constrained to be perpendicular to datum -C. For this configuration dimension b3 replaces dimension b2. Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. This dimension allows for off-center lid, meniscus, and glass overrun. D, D1, and E1 dimensions do not include mold flash or protrusions. Limit diode current to maximum current ratings.

An enable input is provided. The addition of these diodes will reduce the analog signal range to 1V below the positive supply and 1V above the negative supply. Parameter guaranteed by design or characterization. SR Datasheet – Micropower Direct.

  C5200 DATASHEET PDF

Asa cum sunt, la Tine vin!

DGA/DG Quad SPST CMOS Analog Switches

B1 maximum dimensions do not include dambar protrusions. Lab 6 in this note. Package Information continued The package drawing s in this data sheet may not reflect the most current specifications.

Device mounted with all leads soldered to PC board. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its dg201xbk.

No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. Documents Flashcards Grammar checker. Mold flash or protrusions shall not exceed 0. All Rights Reserved All other trademarks mentioned are the property of their respective owners.

DGA Intersil Quad SPST, CMOS Analog Switches ChipFind Datasheet Archive |

The maximum limits of lead dimensions b and c or M shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plate lead finish is applied. Feedthrough via gate capacitance may result in spikes at leading and trailing edge of output waveform.

Typical values are for design aid only, not guaranteed and not subject to production testing.

  LA PRESSE TN ESSAHAFA PDF

Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied.

DG211 Datasheet PDF

Maxim reserves the right to change the circuitry and specifications without notice at any time. Dimension M applies to lead plating and finish thickness. In the OFF state each channel blocks voltages up to the supply rails.

For information regarding Intersil Corporation and its products, see www. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Dambar protrusions shall not exceed 0. A notch or a pin one identification mark shall be located adjacent datashert pin one and shall be located within the shaded area shown.

Maxim guarantees that these switches will not latch up if the power supplies dg201zbk disconnected with input signals still connected. For the latest package outline information, go to www. Dimensions b1 and c1 apply to lead base metal only.