Correction in Service Manual. CX New camera body – new parts .. The operation (except ELX) is fortunately a matter of minutes only. Digital Camera Hasselblad ELX Instruction Manual Camera body ELD Disassembly To remove the parts from the outer and inner The Adobe Acrobat Reader allows you to view and print Hasselblad Historical documents in PDF format. A free copy of the Acrobat Reader is available from.

Author: Vurn Gujin
Country: Paraguay
Language: English (Spanish)
Genre: Photos
Published (Last): 18 November 2014
Pages: 424
PDF File Size: 15.49 Mb
ePub File Size: 16.31 Mb
ISBN: 928-6-96260-537-7
Downloads: 9703
Price: Free* [*Free Regsitration Required]
Uploader: Nikolrajas

Dirt and dust get into your camera, and lubricants dry out and get thick. It should not come off the body with the dark slide removed. You should see a brief, large round flash of light through the lens. I have stocked up on as many of these parts as I can, and I will continue to service the older C lenses as long as my parts supply will permit. Connect the mirror hinge to the two pins “A”. What repxir the proper procedure for attaching or removing extension tubes?

500 EL/M won’t fire with pressing of release button

If you’re still in doubt after that, you can test it by changing it for another one too. What are these things and why do they have to be replaced? You will more than save the price of this booklet on your first magazine repair, and believe me; rdpair or later you are going to need that repair.

The manual came directly from Hasselblad. At that point, lift the transport key again and wind it through at least six or seven turns to wind up the backing paper trailer before opening the magazine and removing the film. There are four holes in this end of the blade.


The procedure is similar for earlier magazines 16 and manial with serial numbers below and magazine 12 with serial numbers between and If you send me a film back for repair and the dark slide is bent or warped, I may replace it without you asking me to.

Camera body ELD Reassembly Place the ruler with indicator clock onto the gauge and move the indicator around the periphery on the front plate and check that the length is within the tolerance.

This manual covers all the bodies except for the focal plane type, and the motorized bodies.

That means it’s trying to work but is being held up mechanicallyspeakingwise” bingo! I made this video to illustrate what’s happening: Use the lubricants listed below: At this point, have an assistant press the lens release button and try to remove the lens from the body.

This manual, which is so very easy to use and understand, can save you hundreds of dollars in body repairs.

Because a bent or warped dark slide can create problems for you. Check that the plug fits smoothly, without gaps.

Remove the cap from the chassis connector and peel back the leather covering the two screws Every picture taken with the magazine that has two extra notches will show those two notches on every negative, and so on.

Take the magazine off the body and remove the dark slide. The shutter blades should close down, then open instantaneously, stay open for one second, and then close again.

If the position of gear is faulty in relation to rear section, this can be adjusted by modifying engagement with gear So the majority of EL That means it’s trying to work but is being held up mechanicallyspeakingwise.

In this case, you will not see any number in the window.

Remove the screw For convenience use the aux. First, remove the lens.


Why did you replace the light trap and nylon stop in my film magazine? Point the camera and the strobe to a light colored surface, and, while looking through the back of the camera body, fire the camera. So here you are with a jammed camera that you can’t wind and the lens won’t come off. It shouldn’t fire after the 12th exposure.

But if you constantly shoot shots and then charge the battery for 7 hours, your battery wouldn’t give you 1, repqir anymore; it would only give around shots. Does anyone out there know how I could go about fixing this without having someone or myself tear down the camera to adjust the release lever?

HASSELBLAD Camera Manuals

Why did you install or replace the brake assembly in my camera body? There was a large rubber disk in this brake, and, after years of use, the disk began to soften up and get gummy. Check each of your lenses using this procedure. In order to insure that the battery will operate at full capacity, it must be fully discharged and fully recharged occasionally.

The manual is illustrated with 17 photos and covers the following:. Not a pleasant experience at all. Unit for infrared remote release of the Hasselblad ELD.

EL/M won’t fire with pressing of release button | Photography Forums

At this point, the number wheel will show the number 1 in the window. When you wind the camera, the number in the film counter window should advance to the next number. Can I use film in my older style Magazine 12?