5. Newsletter. Before doing anything else, make sure to sign up for the free Energy .. Bedini Mono-Pole Energizer circuit that is extremely similar to the diagram. WHAT IS THE BEDINI SG? Get a copy of the Bedini SG – The Authorized Beginner’s Manual if you want to learn all about the Bedini SG and how to build your. This is a hands-on explanation of how to build a monopole energizer based on John C. Bedini’s patent No. 6,, This system charges lead acid or gel cell.

Author: Vudolmaran Guran
Country: Romania
Language: English (Spanish)
Genre: Medical
Published (Last): 25 October 2006
Pages: 68
PDF File Size: 19.86 Mb
ePub File Size: 12.55 Mb
ISBN: 335-2-48743-471-3
Downloads: 40460
Price: Free* [*Free Regsitration Required]
Uploader: Tujinn

The most striking example is the pendulum; during the filming of that segment the pendulum looked very promising but in the end turned out eneggizer be not so great, at least from a battery charging standpoint. Here are the two easiest methods we have found to measure the conventional energy into the charging battery.

Solderingswitchingcircuits to the coils, mounting buss bars. Running load bank watts for 10 hours continous.

John Bedini Monopole Generators

Neon Lamp Purpose – The lamp provides a path for the output energy in case the receiving battery is disconnected while the motor is running. Do not leave the current meter permanently connected as it reduces charge rate. Ensure clips are soldered to wires to ensure proper connection. All messages are moderated and will not appear until approved.


You only need to record the load times after each charging cycle. Basic Tuning Instructions 1. There is a great temptation to use different parts because they are on hand, or to try and improve upon the system.

Monoploe requires time to cycle at least one battery through a charging and loading scheme many times to learn how it responds.

Bedini SSG Monopole Energizer Motor Kit

One power coil drives the south magnet and another power coil drives the north magnet, so no especial and difficult circuit is needed. If you dont mind me asking -Gary. Disconnect the discharge load. Personal aspects have been removed from the dialogue to keep it to science.

Full text of “Bedini Monopole 3 Group Experiment V “

Originally Posted by ren. It is said that this is the setup neccessary to swap the batteries indefinatly as it converts the output of the coils into a form of energy that is better suited to run inductive loads than direct output into the battery. Save those old junk car starter batteries for later.

There are many, many, more Bedini advanced designs that may be replicated for the experimenter’s personal use. I will say that the capacitor version is interesting and it does have at least one advantage over the SSG version: Tolerance – 1 K ohms to 20K ohms, 1 -2 watt. There are also several books and DVDs on the market that may interest you. I think the fifth winding on each coil would be a recovery winding and I don’t think it has a trigger coil.


I feel that something is missing from the recovery in this type of motor, eergizer I think the iron sucks up all the Radiant energy, you may see something different. Sep, try tweaking your base resistance on the front end while monitoring voltage in the cap.

Fixed resistors work best, but you can choose anything where the load is constant.

Also, the front end isn’t directly connected to the back end as in the SSG. Wait until the rotor speed stabilizes, about 1 minute You may see the ammeter fluctuate while the rotor is coming up to speed. Measure the exact ohms of the resistor. Let it come up to speed.

Do at least 20 cycles. Ensure all connections are secure and double check all the circuit connections. The way John Bedini has simplified the Energizer so it is simple to build to anyone with basic skills is a testament to his genius. A dozen recommended for experimental variations e. Wood Stand Purpose – To hold the wheel steady, and to fasten the circuit and hold the coil.

Might have to construct a bicycle wheel rotor. Something interesting is to measure the voltage at the bridge without a capacitor or load in place.